Description
Allturn Upgraded Version 110V-100W Plastic Welder, Plastic – Features & Prices in Saudi Arabia :
Allturn Upgraded Version 110V-100W Plastic Welder, Plastic Welding Kit Car Bumper Repair Kit, Plier, knife,Flat/Outside Corner/Inside Corner/Wave Staples, Plastic Welder Gun .(Yellow)
Manufacturer
JN Buttons
Part Number
PWG-100
Item Weight
4.8 pounds
Package Dimensions
15.91 x 10.91 x 2.72 inches
Color
Yellow
Batteries Included?
No
Batteries Required?
No
Test video – Allturn Upgraded Version 110V-100W Plastic Welder, Plastic :
Product highlights :
Questions & Answers – Allturn Upgraded Version 110V-100W Plastic Welder, Plastic :
Technical specifications – Allturn Upgraded Version 110V-100W Plastic Welder, Plastic :
Purchase advice :
-
Warranty :
Check the duration of the warranty and also the faults and defects it covers. Is it complete or limited? and What is included in the warranty (parts, repairs or both)?
-
Shipping :
Is delivery offered? And how long does it take to get delivered (Delivery time)
-
Proof of purchase :
Does the shop give you an invoice ?
-
After-sales service :
Do they have an after-sales service to have information about the installation or operation (instructions for use). Also in case of problem, it is the seller who takes charge or you must contact the manufacturer or supplier yourself.
_____________________________
![[Pack of 100] Single Use Disposable Blue Face Mask](/wp-content/uploads/2023/05/51k8JL9QgbL-300x225.jpg)
R. C (verified owner) –
Works great and easy to use! – I’ve been using this to fix the various broken plastic parts on my BMW x5. Thankfully nothing major. It’s 15 year old car so typical wear and tear but this has saved me from having to buy three interior panel liners in my trunk lid that had broken clips and drove me nuts every time I closed the lid. Just one of these parts would have cost me $68 so its already paid for itself in my book. Its easy to use and works quick just if you are smoothing the plastic or using the filler use in a well ventilated area.
R. C (verified owner) –
Works great and easy to use! – I’ve been using this to fix the various broken plastic parts on my BMW x5. Thankfully nothing major. It’s 15 year old car so typical wear and tear but this has saved me from having to buy three interior panel liners in my trunk lid that had broken clips and drove me nuts every time I closed the lid. Just one of these parts would have cost me $68 so its already paid for itself in my book. Its easy to use and works quick just if you are smoothing the plastic or using the filler use in a well ventilated area.
L. M (verified owner) –
Heats up quickly, easy to use. – Easy to use.I do upholstery and have to take apart door panels. Plastic etc. This works very well in melting them back together
N. P (verified owner) –
Super Easy – i had several cracks in the hood of my John Deere tractor. After exploring options for glues and epoxies, a friend recommended one of these. One YouTube video later, and I was hooked. Super easy to use and operate. I’ve since recommended this to other friends and family. One side note: Wear eye pro and gloves when you are cutting the tines off the staples. The wire cutters included don’t cut close enough to the “weld” so you will have small pieces of the staple remaining. These can be sharp. Also, when you are cutting off the tines, they have a tendency to fly in every direction. Eye pro prevents one of these little projectiles from ending up in your eye 😉
D. L (verified owner) –
Definitely better then the low wattage versions. – Works way better than the 50-80 watt versions of plastic welder. It is so quick that when you do bigger jobs it overheats and shuts itself down because you are getting too much done and not because it is working to hard to barely accomplish anything like the lower watt ones do. You get a lot more done before it asks for a break. Only done a few different jobs with it so far so cannot attest to longevity but initial ability is wonderful.
I. C (verified owner) –
Easy to use, works great – I purchased the kit to attach a 5 inch piece of plastic on a ski-doo snowmobile side panel, I received the kit and tried the first wire fastener on an old trash can for practice, and then did the repair in a few minutes. Worked great, the repair area had to be strong because it is flexed when attaching it to the snowmobile.
F. M (verified owner) –
Overheats fairly quick – The product does what it is supposed to do, however, I found it overheats quickly and shuts off and it takes several minutes before it resets. I think the body needs to have some ventilation. The body is a solid molded plastic with no air openings. But it did what I needed it to do.
I. C (verified owner) –
Easy to use, works great – I purchased the kit to attach a 5 inch piece of plastic on a ski-doo snowmobile side panel, I received the kit and tried the first wire fastener on an old trash can for practice, and then did the repair in a few minutes. Worked great, the repair area had to be strong because it is flexed when attaching it to the snowmobile.
H. M (verified owner) –
Easy to use, should have bought one years ago! – Very easy to use. Instructions leave a little to be desired, but after reading the complaints it was easy to avoid pitfalls.
D. L (verified owner) –
Definitely better then the low wattage versions. – Works way better than the 50-80 watt versions of plastic welder. It is so quick that when you do bigger jobs it overheats and shuts itself down because you are getting too much done and not because it is working to hard to barely accomplish anything like the lower watt ones do. You get a lot more done before it asks for a break. Only done a few different jobs with it so far so cannot attest to longevity but initial ability is wonderful.
M. R (verified owner) –
Wish I knew this existed sooner! – Seriously a genius concept for a tool. I just wish I knew about it sooner. It’s simple enough for the average DIYer/hobbyists to use and works really well. Before and after photos speak for itself. The tool does have a bit of a learning curve, but nothing you can’t get the hang of after a few applications. Thanks to other’s comments, I found that pulsing the trigger in short 1-2 second bursts makes it easier to control and not burn through the work piece. This thing heats up to melting point almost instantly and cools down nearly as fast. It takes a bit of wiggling back and forth to get the tool of the metal tabs after welding it in. Go gentle with it during removal since it will still be a little hot. I found that the side cutters will not cut the tabs flush and they take a lot of force to cut. Somewhere in the documentation or product info claims you can break the metal tabs off by hand but I didn’t find that to be true. I ended up using the side cutters and then dremeled the rest flush. If you don’t have a rotory grinding tool, they will be much more difficult to get flush.
L. M (verified owner) –
Heats up quickly, easy to use. – Easy to use.I do upholstery and have to take apart door panels. Plastic etc. This works very well in melting them back together
N. P (verified owner) –
Super Easy – i had several cracks in the hood of my John Deere tractor. After exploring options for glues and epoxies, a friend recommended one of these. One YouTube video later, and I was hooked. Super easy to use and operate. I’ve since recommended this to other friends and family. One side note: Wear eye pro and gloves when you are cutting the tines off the staples. The wire cutters included don’t cut close enough to the “weld” so you will have small pieces of the staple remaining. These can be sharp. Also, when you are cutting off the tines, they have a tendency to fly in every direction. Eye pro prevents one of these little projectiles from ending up in your eye 😉
F. M (verified owner) –
Overheats fairly quick – The product does what it is supposed to do, however, I found it overheats quickly and shuts off and it takes several minutes before it resets. I think the body needs to have some ventilation. The body is a solid molded plastic with no air openings. But it did what I needed it to do.
H. M (verified owner) –
Easy to use, should have bought one years ago! – Very easy to use. Instructions leave a little to be desired, but after reading the complaints it was easy to avoid pitfalls.
M. R (verified owner) –
Wish I knew this existed sooner! – Seriously a genius concept for a tool. I just wish I knew about it sooner. It’s simple enough for the average DIYer/hobbyists to use and works really well. Before and after photos speak for itself. The tool does have a bit of a learning curve, but nothing you can’t get the hang of after a few applications. Thanks to other’s comments, I found that pulsing the trigger in short 1-2 second bursts makes it easier to control and not burn through the work piece. This thing heats up to melting point almost instantly and cools down nearly as fast. It takes a bit of wiggling back and forth to get the tool of the metal tabs after welding it in. Go gentle with it during removal since it will still be a little hot. I found that the side cutters will not cut the tabs flush and they take a lot of force to cut. Somewhere in the documentation or product info claims you can break the metal tabs off by hand but I didn’t find that to be true. I ended up using the side cutters and then dremeled the rest flush. If you don’t have a rotory grinding tool, they will be much more difficult to get flush.